english
français
Deutsch
Italiano
Русский
Español
português
Nederlandse
ελληνικά
日本語
한국
polski
فارسی
বাংলা
ไทย
tiếng Việt
العربية
हिन्दी
Türkçe
indonesia
Испытательная скамейка для 8-цилиндрового дизельного насоса для ручного испытания встроенных вращающихся насосов
A 8 Cylinder Diesel Pump Tester is the most affordable diesel pump tester for a diesel service workshop. It is used for manually testing inline and rotatory diesel injection pump. TECHNICAL CHARACTERISTICS: 1 Output power: 7.5 KW 2 Cylinders: 8 cylinders 3 RPM: 0-4000 4 Operation Type: Manual 5 Applicable Pump Type: Inline pumps of K, M, MW, A, B, BV, P (ZU, ZW, ZM) and rotor distributor injection pumps EP/VA, EP/VM, VE.F etc. Подробнее
Испытательная скамейка для многосистемных дизельных топливных насосов для CRDI HEUI EUI EUP
This Diesel Fuel Injection Pump Test Bench is high end, covers the most popular diesel injection systems in the market, inlcuding CRDI injection system, HUIE injection system, and EUI EUP injection system, could test many different diesel injectors and diesel injection pumps. Operation of this diesel test bench is quite easy, just mount the injector or pump on the bench, then connect pipes and cables well, run the software to start the testing. Testing process is fully Подробнее
Механическая дизельная топливная инжекционная насос испытательная скамейка 7,5 кВт до 22 кВт 220В 380В
The Mechanical Injection Pump Test Bench with different power from 7.5kw to 22kw, used for testing mechanical diesel injeciton pump. It has 8 cylinders and 12 cylinders for optional, 220v and 380v voltage was available for different countries. Main Functions : 1 Measure fuel delivery of every cylinder at different speed. 2 Test point and interval angle of fuel supply of injection pump. 3 Check & adjust the mechanical governor. 4 Check & adjust the distributor pump. 5 Test and Подробнее
Многоцелевая испытательная скамейка для дизельного топлива для CRDI HEUI EUI EUP
Multipurpose Diesel Test Bench supports different diesel injection systems, including high pressure common rail injection system, Hydraulic-drive Electrically-controlled Unit Injector injection system, and Electrically-controlled Unit Injector injection system. Equipped with different testing deivce, it could test many different kinds of diesel injectors and injection pumps. Applicable Injection Systme Applicable Injector & Pumps CRDI Injector: Solenoid & Piezo injector Pump: Подробнее
Испытательная скамейка для механических дизельных впрысков для испытаний линейных и VE насосов
Diesel Test bench for Traditional Mechanical Injection Pump, used for testing traditional mechanical inline pumps, as well as VE pumps, which are characterized by stability and reliability. TECHNICAL PARAMETER : 1 Output power: 11 KW 2 Power voltage: 220V/380V 50/60HZ 3 Cylinders: 12 cylinders 4 RPM: 0-4000 5 DC power supply: 12V, 24V 6 Fuel Supply Pressure: High pressure: 0-60bar Low pressure: 0-6bar Inside pressure: 0-16bar 7 Drive Shaft Center Height: 125mm 8 Weight: 810kg Подробнее
Испытательная скамейка для дизельных насосов мощностью 45 кВт для калибровки насосов больших двигателей
It is a 45kw super diesel test bench, for calibration of fuel injectors and injection pumps of heavy duty machinery and generator set. The best solution for testing heavy duty injection pumps, like QSK19, QSK38, QSK60, QSK50, MTU2000 new and old style, MTU4000 new and old style etc. TECHNICAL PARAMETER : 1 Output power: 45 KW 2 Power voltage: 380V 3 RPM: 0-4000 4 Speed Control: Frequency Converter 5 Max. Rail Pressure: 2700 bar 6 Diesel tank capacity: 40L 7 Weight: 1934kg 8 Подробнее
Испытательная скамейка для механических дизельных топливных насосов для серии KMW A B P
Diesel injection pump tester is basic equipment for a diesel injection laboratory, used to test mechanical injection pump. It could test inline pumps of K, M, MW, A, B, BV, P (ZU, ZW, ZM) and rotor distributor injection pumps EP/VA, EP/VM, VE.F etc. TECHNICAL PARAMETER : 1 Output power: 7.5/11/15/18.5/22 KW 2 Power voltage: 220V/380V 3 Cylinders: 8 or 12 cylinders 4 RPM: 0-4000 5 DC power supply: 12V, 24V 6 Weight: 800kg 7 Packing Dimension: (H*W*L) 2140*1100*1820 mm Подробнее
8 цилиндров дизельного топлива насос для впрыска испытательная скамейка 7,5 кВт линейный вращающийся
The smallest injection pump tester is 8 cylinders, which is 7.5kw. It has a small size, could test inline and rotatory injection pump, highly reliable and affordable. TECHNICAL PARAMETER: 1 Output power: 7.5 KW 2 Power voltage: 220V/380V 3 Cylinders: 8 cylinders 4 RPM: 0-4000 5 DC power supply: 12V, 24V 6 Weight: 650kg 7 Dimension: (H*W*L) 1700*800*800 mm Подробнее
Дизельное топливо инжекционный насос испытательная скамейка 22KW нержавеющая сталь двойного резервуара воздушного компрессора
It is a high end Diesel Injection Pump Tester, equipped with a 22kw AC main motor, two stainless steel fuel tanks with two individual motors, beside, there is an air compressor with the tester. except testing mechanical Inline & Rotary injection pump, could also test RED4 pump, Generator electronically controlled governor pump, and check ZME/SCV/IMV valve of electronic pump. MAIN FUNCTIONS: 1 Test conventional mechanical Inline & Rotary injection pump. 2 Test RED4 pump 3 Test Подробнее
